The BSA A7-A10 Forum
Technical (Descriptive Topic Titles - Stay on Topic) => Lucas, Ignition, Charging, Electrical => Topic started by: bl**dydrivers on 13.02. 2017 02:50
-
Anyone have experience with the reproduction Lucas SSU700P from India and or Taiwan?
How are they? And have I got a better option?
-
Anyone?
I wasn't lucky to have the original one.
-
I've got a spare ss700p shell (no switch/ammeter) and the repros I've seen are ok except the underslung pilot light sections are the wrong shape, too deep and the glass shape quite different, but better than nothing I guess.
The attached pic shows my original (on the left) versus a repro, there may be better repros around of course.
-
My experience with Indian parts is they are OK if you want to ride the motorcycle. If you want perfection I would suggest recondition original parts or buy pattern parts from a dealer that will take back junk. HTH
-
Tomcat,
I was going to reply to you last night but got busy.
Between India and Taiwan, im going Taiwan.
I dont understand these guys in India. They obviously have the ability to move sheet metal, even by hand some seem very talented. Others, not so much. The gauge of metal they use is fine, its not tin foil.
Why cant they pull their heads out of their butts and make parts the right shape? Most times, they are "close" but off just enough.
Lee
Then I hear of parts that are rusting in transit. How much does it take to soak these parts in 50% vinegar/ 50% water and give them a rub with scotchbrite to protect them from rust? Or spray them down and wipe them off with your favorite used motor oil and send them wrapped inside a garbage bag? Yes, oiled new parts is a pain for the painter, but its easier to deal with than rust. Especially on something inside like a tank.
They all want to sell 10,000 parts, which is fine. Whichever one figures out correctly shaped, protected parts is what people want will sell them.
These cats that spend the time to write "bestest quality" and figuring out who is going to pay return shipping are not getting it done.
-
Tomcat,
I was going to reply to you last night but got busy.
Between India and Taiwan, im going Taiwan.
I dont understand these guys in India. They obviously have the ability to move sheet metal, even by hand some seem very talented. Others, not so much. The gauge of metal they use is fine, its not tin foil.
Why cant they pull their heads out of their butts and make parts the right shape? Most times, they are "close" but off just enough.
Lee
Then I hear of parts that are rusting in transit. How much does it take to soak these parts in 50% vinegar/ 50% water and give them a rub with scotchbrite to protect them from rust? Or spray them down and wipe them off with your favorite used motor oil and send them wrapped inside a garbage bag? Yes, oiled new parts is a pain for the painter, but its easier to deal with than rust. Especially on something inside like a tank.
They all want to sell 10,000 parts, which is fine. Whichever one figures out correctly shaped, protected parts is what people want will sell them.
These cats that spend the time to write "bestest quality" and figuring out who is going to pay return shipping are not getting it done.
What you have to remember in India the person who sells them is not the person who makes them.
The man who makes them gets paid 10p and the man who plates them get paid 10p and the man who makes the glass gets paid 5p then they might pass through 20 sets of hands all making a cut before you pay £ 15.00 for the "finished product".
In Taiwan there is a real factory that makes the entire product and relies on repeat orders so the quality is higher.
-
Thanks Trevor. So who retails the Taiwanese parts?
-
Most of the regular Pommie Bike dealers.
-
In the end I was lucky to come across an original SSU700P, complete with headlight switch, ammeter and reflector. Wondering if I can replace parts of the original switch with pattern parts! But looking for a new reflector as the one that came with it is the sealed type typically used in the US at the time.
Ammeter will replace it with a new one and looking forward to seeing the results of the headlight coming back from being painted.