View or Hide Header -->
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
This topic
This board
A7 & A10 Engine
A7 1946-1950
Gearbox, Clutch, Primary
Frame
Lucas, Ignition, Charging, Electrical
Amal, Carburation
Entire forum
Google
Home
Help
Search
Contact
Login
Register
The BSA A7-A10 Forum
»
Technical (Descriptive Topic Titles - Stay on Topic)
»
A7 & A10 Engine
»
Oil return pick-up tube.
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Oil return pick-up tube. (Read 958 times)
coater87
Wise & Enlightened
Join Date: Jul 2008
Posts: 1204
Karma: 6
Oil return pick-up tube.
«
on:
09.03. 2017 20:04 »
Mine is either bent, or the sump plate and strainer I got from SRM is made different.
How fragile is this tube, is it likely to snap right off?
Or am I better off modifying the strainers to get the pick-up to poke through?
Lee
Logged
Central Wisconsin in the U.S.
morris
Wise & Enlightened
Join Date: Aug 2012
Posts: 1768
Karma: 27
Antwerp, Belgium
Re: Oil return pick-up tube.
«
Reply #1 on:
09.03. 2017 20:22 »
I had the same problem on the plunger. The PO had solved it by enlarging the hole in the strainer.
I didn't like that solution so I bought a new one which didn't fit either so I took a deep breath and a pair of flat jaw pliers and managed to bend the pipe to fit the hole. Mind you, it was only about 2 or 3 mm out.
But don't hold me responsible if you try the same and end up breaking it off...
Logged
'58 BSA A 10 SA
'52 BSA A 10 Plunger
'55 MORRIS ISIS
The world looks better from a motorbike
Belgium
coater87
Wise & Enlightened
Join Date: Jul 2008
Posts: 1204
Karma: 6
Re: Oil return pick-up tube.
«
Reply #2 on:
09.03. 2017 20:30 »
Morris,
Mine is out a lot. If you were worried about a couple millimeters, I need to be complete frozen with fear
Let me see if I can get a picture posted.
Lee
Logged
Central Wisconsin in the U.S.
coater87
Wise & Enlightened
Join Date: Jul 2008
Posts: 1204
Karma: 6
Re: Oil return pick-up tube.
«
Reply #3 on:
09.03. 2017 21:10 »
If these show up, mine is way off.
Looking at the strainer, it actually does not seem bent. Maybe its pushed in a little, but certainly not that much.
I tried flipping it this way and that, no joy.
Its either bend it, or butcher it.
Lee
Logged
Central Wisconsin in the U.S.
morris
Wise & Enlightened
Join Date: Aug 2012
Posts: 1768
Karma: 27
Antwerp, Belgium
Re: Oil return pick-up tube.
«
Reply #4 on:
09.03. 2017 22:07 »
Quote from: coater87 on 09.03. 2017 21:10
Its either bend it, or butcher it.
Sums it all up!
I used this type of strainer which is a bit more difficult to cut out;
http://www.degroot-bsa.nl/index.php?route=product/product&path=47_80&product_id=2239
Logged
'58 BSA A 10 SA
'52 BSA A 10 Plunger
'55 MORRIS ISIS
The world looks better from a motorbike
Belgium
chaterlea25
Wise & Enlightened
Join Date: Jun 2009
Posts: 4026
Karma: 54
Re: Oil return pick-up tube.
«
Reply #5 on:
09.03. 2017 22:42 »
HI All,
The pickup pipe is pressed into the crankcase
The bend relatively easily, but do not just try to bend the bottom end of the tube,
Lever the pipe higher up,
With a dismantled engine I have heated up the case and moved the pipe in the alloy
John
Logged
1961 Super Rocket
1963 RGS (ongoing)
beezermacc
Guest
Re: Oil return pick-up tube.
«
Reply #6 on:
09.03. 2017 23:33 »
Unfortunately the suction pipe is easily knocked when the crankcases are rolling around on the bench or garage floor. Nobody here would treat them like that but you can bet they've been falling off a shelf in a shed many years ago when they were virtually worthless. Also it is important that the suction pipe is not loosened in the crankcase half as it will suck air at the joint rather than oil, a reason why some A10's seem to fill up with oil..... anyway, I digress. The best solution I've found to adjusting the alignment of the sump screen is to slightly enlarge the holes in the corners to provide a bit of 'wriggle room'.
Logged
coater87
Wise & Enlightened
Join Date: Jul 2008
Posts: 1204
Karma: 6
Re: Oil return pick-up tube.
«
Reply #7 on:
10.03. 2017 00:49 »
Morris,
I dont know why but I got the screen you see in the photos, and the screen you show. But, I only got enough gaskets for one or the other.
In my case, if either one of them fit that would be the one that got used.
Its off a lot. Maybe someone knows where screen like this can be bought?
I dont know if bending and making "wriggle" room would even get me enough, or if I would just end up making the situation worse by breaking the pipe or loosening the joint.
Lee
Logged
Central Wisconsin in the U.S.
KiwiGF
Last had an A10 in 1976, in 2011 it was time for my 2nd one. It was the project from HELL (but I learned a lot....)
Wise & Enlightened
Join Date: Feb 2011
Posts: 1940
Karma: 17
Re: Oil return pick-up tube.
«
Reply #8 on:
10.03. 2017 06:59 »
The tube was not a tight fit in the case on my bike, it was removed by the machinest when he was milling the step in the cases flat in the sump plate surface area, I simply slid it back into place, using a gauze as a guide, and with some loctite to hold it in place.....
So, if you heat the tube you MIGHT find whatever glue is holding it place will soften, and it will move easily.
Worth a try anyway I reckon
Logged
New Zealand
1956 A10 Golden Flash (1st finished project)
1949 B31 rigid “400cc” (2nd finished project)
1968 B44 Victor Special (3rd finished project)
2001 GL1800 Goldwing, well, the wife likes it
2009 KTM 990 Adventure, cos it’s 100% nuts
Butch (cb)
Wise & Enlightened
Join Date: Aug 2010
Posts: 1691
Karma: 16
Re: Oil return pick-up tube.
«
Reply #9 on:
10.03. 2017 07:47 »
Mine wasn't a perfect fit but not as bad as that. I kind of nibbled bits of mesh away until it went through without straining (see what I did there?), and then soft soldered at the bit of gap I now had to minimise that.
Logged
Warning - observations made by this member have a 93% unreliability rating.
Of Bikes; various, including ...
'58 S/Arm Iron Head Flash Bitza
bikerbob
Resident Legend
Join Date: Feb 2011
Posts: 680
Karma: 8
Re: Oil return pick-up tube.
«
Reply #10 on:
10.03. 2017 09:04 »
Looking at the strainer and the pipe even if the pipe was to fit central in the hole the remaining gap between the pipe and the strainer would be bigger than the holes in the strainer therefore defeating the purpose of the strainer. I would be tempted to enlrge the whole in the strainer until it fitted over the pipe then solder a home made washer onto the strainer covering up the gap. Or you could measure the holes per inch in the strainer and buy the same material and make your own strainer to suit you can buy material like that on ebay. I have done it and renewed the mesh on my oil filter and petrol filters.
Logged
56 A7 s/a
63 A65
KiwiGF
Last had an A10 in 1976, in 2011 it was time for my 2nd one. It was the project from HELL (but I learned a lot....)
Wise & Enlightened
Join Date: Feb 2011
Posts: 1940
Karma: 17
Re: Oil return pick-up tube.
«
Reply #11 on:
10.03. 2017 10:10 »
Although like many I have fallen out with Draganfly that gauze looks pretty cheap compared with the Draganfly equivalent that I bought from them........see
https://www.draganfly.co.uk/index.php/accessories-a-misc/product/16249-
Logged
New Zealand
1956 A10 Golden Flash (1st finished project)
1949 B31 rigid “400cc” (2nd finished project)
1968 B44 Victor Special (3rd finished project)
2001 GL1800 Goldwing, well, the wife likes it
2009 KTM 990 Adventure, cos it’s 100% nuts
coater87
Wise & Enlightened
Join Date: Jul 2008
Posts: 1204
Karma: 6
Re: Oil return pick-up tube.
«
Reply #12 on:
10.03. 2017 18:37 »
I have worked at unfolding the edge around this strainer, hoping I can rotate the screen to a better position and then crimp the thing back down but its not working.
I have no knowledge of the wizardry used to make this flimsy thing, and its become more and more bent out of shape (read: damn near unusable already).
I have looked at many of these for sale, and they all look clocked to the same angle.
I am going to have to make something up because I cannot get up the balls to go after mine with a torch and pliers.
Lee
Logged
Central Wisconsin in the U.S.
coater87
Wise & Enlightened
Join Date: Jul 2008
Posts: 1204
Karma: 6
Re: Oil return pick-up tube.
«
Reply #13 on:
10.03. 2017 19:51 »
Using nothing but buckets full of brute force and ignorance I have succeeded!
This was a PIA, but it did work. I still may have to file a bit to get some wriggle room, but its 200% better than it was.
Logged
Central Wisconsin in the U.S.
chaterlea25
Wise & Enlightened
Join Date: Jun 2009
Posts: 4026
Karma: 54
Re: Oil return pick-up tube.
«
Reply #14 on:
10.03. 2017 20:51 »
Hi Lee,
Well done on sorting the problem, Theres more than one way to skin a cat (or filter screen)
I'm puzzled by the description of the draganfly item
"Filter plate, large hole 71-1126"
John
Logged
1961 Super Rocket
1963 RGS (ongoing)
Print
Pages: [
1
]
Go Up
« previous
next »
The BSA A7-A10 Forum
»
Technical (Descriptive Topic Titles - Stay on Topic)
»
A7 & A10 Engine
»
Oil return pick-up tube.