Author Topic: A10 won't start :(  (Read 872 times)

Offline owain

  • A's Best Friend
  • ***
  • Join Date: Mar 2017
  • Posts: 135
  • Karma: 2
A10 won't start :(
« on: 02.07. 2018 21:17 »
My 1950 A10 plunger (with sidecar) is showing no signs of life at all. The bike has been running great until a few weeks ago when the exhaust rocker box gasket split and lots of oil came out. No big deal, I thought. So I when I got home, I took the rocker boxes off, fitted a new gasket and recalibrated the valve clearances and double checked them. Started the bike and away I went.

A couple of days later, I went for another bike ride and started to encounter problems. A few minutes into my journey the engine stopped when I was at the traffic lights. Then a few minutes later, it started to splutter. I remedied this by giving it some more throttle and started to make my way home. Then the real trouble happened. The engine started to only fire on one cylinder. I stopped. Tried to see if the cables from the magneto had came loose. Nope. Managed to get the engine going again after two dozen kicks. Still running on one cylinder. Instead of abandoning the bike by the side of the road, I decided to rough it out and make the 2 mile trip home running on one cylinder.

Now comes my diagnostics:
Carburettor has not been touched in months. I checked the carb nonetheless (Jets, float level). Everything appears to be fine.
Could the spark plugs have fouled? The spark plugs looked a little (but not very) black. So I placed new spark plugs in. Engine still wouldn't start.
Could the bike have wet sumped? Drained the crankcase of oil. Engine still wouldn't start.
Could the valve clearance be wrong? Triple checked valve clearance. All within spec. Engine still wouldn't start.
Could I have bad compression? Checked compression and found each cylinder to have 150psi. Plenty of pressure. Not that then.

So it must be the ignition!.My magneto was well overdue a restoration so I sent it to APL magnetos. Got it back a week later. Set the timing i.e. when the points just begin to separate at 11/32" before TDC on the compression stroke. Made sure that I tightened the double threaded nut back on with the auto-advance unit wedged in the fully advanced position....Engine didn't start!
Repeated this step five more times. Engine still won't start.

Finally, failing to see any other alternatives. I emptied the tanks petrol and filled it with a gallon of fresh petrol. Still no luck.

Does anyone else have any idea about what could possibly be preventing this motorcycle from starting/running? I'm all out of ideas. Cheers :)

Sweden & North Wales
'50 BSA A10
'69 BSA A75R

Online mugwump

  • A's Best Friend
  • ***
  • Join Date: Jan 2016
  • Posts: 105
  • Karma: 0
Re: A10 won't start :(
« Reply #1 on: 02.07. 2018 22:28 »
Presumably you have checked that there is a good spark. Have you tried switching the plug leads around, having re-fitted the mag and re-timed it. Are the ht leads and connections good and no chance of tracking. Can't think of anything more as you seem to have covered most other possibilities. Do update the form when sorted please.

60'Matchy G12
58 AJS 18s
58 Ariel Huntmaster]

Online Greybeard

  • Jack of all trades; master of none.
  • Wise & Enlightened
  • *
  • Join Date: Feb 2011
  • Posts: 6206
  • Karma: 35
Re: A10 won't start :(
« Reply #2 on: 02.07. 2018 23:40 »
If any petrol engine has sucked in a mixture of air and petrol vapour, has a healthy spark at the plugs, occurring at the correct time and has cylinder compression it must at least fire, if not continue to run. So, check the basics again.

Online KiwiGF

  • Last had an A10 in 1976, in 2011 it was time for my 2nd one. It was the project from HELL (but I learned a lot....)
  • Wise & Enlightened
  • *
  • Join Date: Feb 2011
  • Posts: 1466
  • Karma: 12
Re: A10 won't start :(
« Reply #3 on: 02.07. 2018 23:51 »
My 1950 A10 plunger (with sidecar) is showing no signs of life at all. The bike has been running great until a few weeks ago when the exhaust rocker box gasket split and lots of oil came out. No big deal, I thought. So I when I got home, I took the rocker boxes off, fitted a new gasket and recalibrated the valve clearances and double checked them. Started the bike and away I went.

A couple of days later, I went for another bike ride and started to encounter problems. A few minutes into my journey the engine stopped when I was at the traffic lights. Then a few minutes later, it started to splutter. I remedied this by giving it some more throttle and started to make my way home. Then the real trouble happened. The engine started to only fire on one cylinder. I stopped. Tried to see if the cables from the magneto had came loose. Nope. Managed to get the engine going again after two dozen kicks. Still running on one cylinder. Instead of abandoning the bike by the side of the road, I decided to rough it out and make the 2 mile trip home running on one cylinder.

Now comes my diagnostics:
Carburettor has not been touched in months. I checked the carb nonetheless (Jets, float level). Everything appears to be fine.
Could the spark plugs have fouled? The spark plugs looked a little (but not very) black. So I placed new spark plugs in. Engine still wouldn't start.
Could the bike have wet sumped? Drained the crankcase of oil. Engine still wouldn't start.
Could the valve clearance be wrong? Triple checked valve clearance. All within spec. Engine still wouldn't start.
Could I have bad compression? Checked compression and found each cylinder to have 150psi. Plenty of pressure. Not that then.

So it must be the ignition!.My magneto was well overdue a restoration so I sent it to APL magnetos. Got it back a week later. Set the timing i.e. when the points just begin to separate at 11/32" before TDC on the compression stroke. Made sure that I tightened the double threaded nut back on with the auto-advance unit wedged in the fully advanced position....Engine didn't start!
Repeated this step five more times. Engine still won't start.

Finally, failing to see any other alternatives. I emptied the tanks petrol and filled it with a gallon of fresh petrol. Still no luck.

Does anyone else have any idea about what could possibly be preventing this motorcycle from starting/running? I'm all out of ideas. Cheers :)

Plug leads around wrong way is most likely, as a long shot check the tickler, which doubles as a breather for the float chamber, is not blocked. If you rule out ignition as the cause of the problem and you have a monobloc you can can check the float is working correctly using cling film and a rubber band.

If you have a concentric carb cleaning out the idle jet is NOT that easy to do properly, what carb do you have!
New Zealand

1956 A10 Golden Flash (1st finished project)

1949 B31 rigid “400cc hot rod” (2nd finished project, + favourite bike)

GL1800 Goldwing, well, the wife likes it

KTM 950 ADV, cos it’s 100% nuts

1952 Armstrong Siddeley Whitley for rainy days (with wife)

Offline owain

  • A's Best Friend
  • ***
  • Join Date: Mar 2017
  • Posts: 135
  • Karma: 2
Re: A10 won't start :(
« Reply #4 on: 03.07. 2018 10:24 »
I've checked whether I'm getting a spark with a spark tester (getting a strong flash from the light bulb). I also removed the spark plugs, connected the plug leads and saw a good spark. I know that compression makes it more difficult for a weak spark to jump the gap, I wouldn't expect there to be a weak spark from a newly reconditioned magneto though...

I'm running an amal concentric carb on the bike. Petrol squirts out of the tickler when tickling the carb, so I think that is clear. A new pilot jet was fitted to the carb last year but even so, I tend to start the bike with the throttle half open. :/

I'll swap the leads and give it a go and will try to fiddle with the timing again. After my previous attempts of setting the timing, I was getting the odd flame out of the carb. Then I changed the timing again and I got the occassional flame out of the exhaust pipe. After my last attempt of setting the timing at 11/32" before TDC the engine won't combust at all.
Sweden & North Wales
'50 BSA A10
'69 BSA A75R

Online JulianS

  • 1962 A10
  • Wise & Enlightened
  • *
  • Join Date: Mar 2017
  • Posts: 1010
  • Karma: 20
Re: A10 won't start :(
« Reply #5 on: 03.07. 2018 11:09 »
Only the early 4 stroke and new premier concentrics had a removable pilot jet (Though in different places). But they still had a threaded hole to take one.  The other models had a pressed in non removable difficult to clean one.  This link to Amal details rebuilding a concentric and cleaning a pressed in jet;

http://amalcarb.co.uk/rebuilding-mark-1-concentric-carburetter

Online KiwiGF

  • Last had an A10 in 1976, in 2011 it was time for my 2nd one. It was the project from HELL (but I learned a lot....)
  • Wise & Enlightened
  • *
  • Join Date: Feb 2011
  • Posts: 1466
  • Karma: 12
Re: A10 won't start :(
« Reply #6 on: 03.07. 2018 11:15 »
Only the early 4 stroke and new premier concentrics had a removable pilot jet (Though in different places). But they still had a threaded hole to take one.  The other models had a pressed in non removable difficult to clean one.  This link to Amal details rebuilding a concentric and cleaning a pressed in jet;

http://amalcarb.co.uk/rebuilding-mark-1-concentric-carburetter

Great minds think alike eh! I was going to post that link but you beat me to it, also I noticed it does not mention cleaning the air way from the rear of the carb to the “mixing chamber” behind the pilot adjuster screw. I was trying to find a pic of the whole pilot circuit but haven’t yet.

At this stage I think it’s possible the idle jet is blocked, but more it’s likely an ignition issue.
New Zealand

1956 A10 Golden Flash (1st finished project)

1949 B31 rigid “400cc hot rod” (2nd finished project, + favourite bike)

GL1800 Goldwing, well, the wife likes it

KTM 950 ADV, cos it’s 100% nuts

1952 Armstrong Siddeley Whitley for rainy days (with wife)

Online mugwump

  • A's Best Friend
  • ***
  • Join Date: Jan 2016
  • Posts: 105
  • Karma: 0
Re: A10 won't start :(
« Reply #7 on: 03.07. 2018 13:24 »
Owain, do you check that the timing has not moved after you have set it. And, are the points gap still at 13thou.

60'Matchy G12
58 AJS 18s
58 Ariel Huntmaster]

Offline Billybream

  • Resident Legend
  • *****
  • Join Date: Jan 2012
  • Posts: 524
  • Karma: 6
Re: A10 won't start :(
« Reply #8 on: 03.07. 2018 13:25 »
Are the spark plugs getting wetted with fuel. Is the petrol tank vent clear.
Try disconnecting the kill lead on the mag.
A problem I experienced recenty was the needle was incorrectly fitted and was not rising with the slide, should be easy to check from the intake bellmouth.
1960 Super Rocket, owned since 1966, back on the road 2012 after being laid up for 29yrs.

Online RichardL

  • Outside Chicago, IL
  • Wise & Enlightened
  • *
  • Join Date: Nov 2007
  • Posts: 5064
  • Karma: 48
Re: A10 won't start :(
« Reply #9 on: 03.07. 2018 13:30 »
Only the early 4 stroke and new premier concentrics had a removable pilot jet (Though in different places). But they still had a threaded hole to take one.  The other models had a pressed in non removable difficult to clean one.  This link to Amal details rebuilding a concentric and cleaning a pressed in jet;

http://amalcarb.co.uk/rebuilding-mark-1-concentric-carburetter

In case you have to clean a concentric's pilot jet, some folks use an 0.016 guitar string. My approach was to go with the #78 drill method, as described here:

https://www.a7a10.net/forum/index.php?topic=11619.msg89032#msg89032

Richard L.


Plan on signing up for the world-wide 2020 DISTINGUISHED GENTLEMAN'S RIDEon September 27, 2020 (if it's not cancelled and we are free to move about by then). Watch website at https://www.gentlemansride.com for details.

Online Greybeard

  • Jack of all trades; master of none.
  • Wise & Enlightened
  • *
  • Join Date: Feb 2011
  • Posts: 6206
  • Karma: 35
Re: A10 won't start :(
« Reply #10 on: 03.07. 2018 13:40 »
I'll swap the leads and give it a go and will try to fiddle with the timing again. After my previous attempts of setting the timing, I was getting the odd flame out of the carb. Then I changed the timing again and I got the occassional flame out of the exhaust pipe. After my last attempt of setting the timing at 11/32" before TDC the engine won't combust at all.

I recently got my plug leads reversed after timing and had some pops and bangs before I swapped the leads over.

Online Black Sheep

  • Resident Legend
  • *****
  • Join Date: Apr 2017
  • Posts: 677
  • Karma: 6
    • Where black sheep live
Re: A10 won't start :(
« Reply #11 on: 03.07. 2018 14:07 »
If you start on half throttle, there is something badly wrong with your carb setup. Sort out the pilot jet as mentioned above.
2 twins, 2 singles, lots of sheep

Offline owain

  • A's Best Friend
  • ***
  • Join Date: Mar 2017
  • Posts: 135
  • Karma: 2
Re: A10 won't start :(
« Reply #12 on: 03.07. 2018 18:55 »
Update:
Sprayed a little bit of starter spray through the carb. Started straight away! FFS!
Sweden & North Wales
'50 BSA A10
'69 BSA A75R

Online Greybeard

  • Jack of all trades; master of none.
  • Wise & Enlightened
  • *
  • Join Date: Feb 2011
  • Posts: 6206
  • Karma: 35
Re: A10 won't start :(
« Reply #13 on: 03.07. 2018 19:52 »
Update:
Sprayed a little bit of starter spray through the carb. Started straight away! FFS!

 *smile*
I'm glad it fired up; shows there is nothing much wrong. Have you been able to start it normally since then?

Offline owain

  • A's Best Friend
  • ***
  • Join Date: Mar 2017
  • Posts: 135
  • Karma: 2
Re: A10 won't start :(
« Reply #14 on: 04.07. 2018 20:03 »
Ah well I may have spoken too soon actually. It seemed to run ok yesterday. It wasn't sounding very good today though. When I accelerate it sounds good. When I'm cruising it sounds like it's 'hiccuping'/ running a bit poorly. I thought that maybe this could be due to the timing being slightly off. If I didn't give it any throttle. It dies on idle. I had to twist the idle screw in the carb really far in to keep it alive at a fast idle.

I'm thinking of taking the carb apart checking all the jets e.g. blowing them out with compressed air. Then giving it a go again. If it is still running a bit off when cruising then I'll reset the timing again to see if that improves the situation  *???*
Sweden & North Wales
'50 BSA A10
'69 BSA A75R