Author Topic: Another Clutch Question  (Read 700 times)

Offline A10 JWO

  • Resident Legend
  • *****
  • Join Date: Oct 2012
  • Posts: 730
  • Karma: 2
Another Clutch Question
« on: 12.07. 2018 16:01 »
Just fitted a Brand New SRM complete clutch. The bike started on the kick start but after I added the correct amount of oil I have slight slip on the kick start. I don't want to keep taking the cover off, so my question is, how many turns do I take up the springs to get this right. Thank you.

Online JulianS

  • 1962 A10
  • Wise & Enlightened
  • *
  • Join Date: Mar 2017
  • Posts: 1385
  • Karma: 29
Re: Another Clutch Question
« Reply #1 on: 12.07. 2018 16:47 »
I fitted an SRM clutch in the spring, exactly as per the instructions, including the oil, not ATF.

It dragged for about 10 miles, then settled, and is light, no drag no slip.

I would ride it a few miles to let it all bed in and if you still have a problem contact SRM to discuss.

Offline A10 JWO

  • Resident Legend
  • *****
  • Join Date: Oct 2012
  • Posts: 730
  • Karma: 2
Re: Another Clutch Question
« Reply #2 on: 12.07. 2018 17:17 »
Hi Julian. I can't start it now because of the slipping, don't want to wind the screws in too much ? Those gaskets are not cheap LOL. Thanks.

Online JulianS

  • 1962 A10
  • Wise & Enlightened
  • *
  • Join Date: Mar 2017
  • Posts: 1385
  • Karma: 29
Re: Another Clutch Question
« Reply #3 on: 12.07. 2018 17:57 »
Should not need to screw them in very far, mine is very light, 2 fingers to operate.

Have you got enough clearance on the pushrod?

Offline A10 JWO

  • Resident Legend
  • *****
  • Join Date: Oct 2012
  • Posts: 730
  • Karma: 2
Re: Another Clutch Question
« Reply #4 on: 12.07. 2018 22:18 »
There is another thread on SRM Clutches which shows a picture of the springs according to SRM. Will have another go in the morning, push rod has about 3 mm slack, thanks.

Offline chaterlea25

  • Wise & Enlightened
  • *
  • Join Date: Jun 2009
  • Posts: 4015
  • Karma: 54
Re: Another Clutch Question
« Reply #5 on: 12.07. 2018 22:43 »
Hi All,
With the SRM clutch you need to check for pushrod  free play at the clutch end
If set up incorrectly the "pusher" can butt up against the end of the mainshaft, resulting in clutch slip

John
1961 Super Rocket
1963 RGS (ongoing)

Offline A10 JWO

  • Resident Legend
  • *****
  • Join Date: Oct 2012
  • Posts: 730
  • Karma: 2
Re: Another Clutch Question
« Reply #6 on: 13.07. 2018 17:35 »
Took cover plate off and checked the parts. I applied a slight amount of grease on springs and top hat bearing. Re-assembled as per enclosed instructions. They suggest adjusting allen key bolt till it bites then slacken off one full turn. I could only slacken off 7/8's of a turn so the push rod is very slightly too long. Hopefully after 10 miles as suggested it will bed in and give me a bit more slack. The clutch is working fine and doing what it said on the box. Ride out tomorrow  *eek*