Author Topic: Engine breather  (Read 1196 times)

Online BigJim

  • Resident Legend
  • *****
  • Join Date: Aug 2018
  • Posts: 537
  • Karma: 2
  • Bristol. UK
Engine breather
« on: 04.09. 2019 22:51 »
Hello,
Have zero endfloat on my breather but have sideways movement of approx 3mm as it is loose on the locating peg. this is evident with the inner timing case in place. Should i be concerned about this and try to stop sideways play?
 Have an oily top end and some oil exiting through the breather hole, might the sideways play be contributing to this?
Cheers
Jamie,  Supporter of Distinguished Gentleman's Ride

Offline Rocket Racer

  • Wise & Enlightened
  • *
  • Join Date: Jun 2009
  • Posts: 1670
  • Karma: 17
  • A kiwi with a racing A10 rig and too many projects
    • NZ Classic Sidecar Racing
Re: Engine breather
« Reply #1 on: 05.09. 2019 06:02 »
if your cork gasket shim is doing its job the breather should be firmly held and not able to rotate on the pin.If its rotating as you indicate you still have excess breather clearance and that may contribute to oil loss via the breather. 
Is the smokey motor due to excess oil in the motor or just wear in rings/valves? excess blowby could cause crankcase pressure.
Quite a few variables there.
Presumably the motor isnt wet sumped at start up as that will definitely give you grief.
A good rider periodically checks all nuts and bolts with a spanner to see that they are tight - Instruction Manual for BSA B series, p46, para 2.
New Zealand

Offline Swarfcut

  • Wise & Enlightened
  • *
  • Join Date: Oct 2018
  • Posts: 2201
  • Karma: 54
Re: Engine breather
« Reply #2 on: 05.09. 2019 07:37 »
Jim, The breather will be driven OK by the peg, but will obviously be running  slightly "retarded" for optimum operation of the timed breather as designed. Replacing the worn breather and cam wheel is the easiest and most expensive option. If just the peg is worn it can be replaced, or a new hole for the peg drilled in the breather flange opposite the original, depending on your skill and engineering facilities. The breather also needs to be a good close fit in the inner timing case, where it rotates, and the cork washer thickness chosen to be under slight compression to ensure an airtight seal between cam wheel and breather flange, when the inner cover is tightened into place. Too thick a washer will put a lot of load on the parts and wear the timing cover and breather flange.

 At least changing the parts and correct assembly will eliminate a poor breather as a source of the oil problems.

Swarfy.

Online Klaus

  • Valued Contributor
  • ****
  • Join Date: Jun 2015
  • Posts: 438
  • Karma: 10
Re: Engine breather
« Reply #3 on: 05.09. 2019 08:22 »
The cork washers are a pain, and have to be grind to correkt thickness. So I convert to use a spring to held the breather in place. Running in seval engine since thousands of miles with no problems.

cheers Klaus


If you think, everything is under control, you are not fast enought.

BSA DB34 Goldstar, BSA A10 Road Rocked, BSA A7 Shooting Star, BSA M33, BSA M24, Kawa W650

Online BigJim

  • Resident Legend
  • *****
  • Join Date: Aug 2018
  • Posts: 537
  • Karma: 2
  • Bristol. UK
Re: Engine breather
« Reply #4 on: 05.09. 2019 08:34 »
Thank you gents. Will see what i can do with a slightly thicker cork rubbed down to fit. Have little engineering abilities Swarthy so replacement with new is more likely but not for a while. No wet sumping Rocket R and clinging to hope it's not blowby as engine build is only 2500 (approx) old.
Will also be trying to ride a little more gently!
Thanks again.
Jamie,  Supporter of Distinguished Gentleman's Ride

Offline duTch

  • Ricketty Rocketty Golden Flashback
  • Wise & Enlightened
  • *
  • Join Date: Oct 2011
  • Posts: 4528
  • Karma: 41
Re: Engine breather
« Reply #5 on: 05.09. 2019 10:11 »

 Jim- due to lack of cork thickness options, to pack it out, I used gasket paper shims behind the cork I had- you could probably use any oil resistant material to do same.... and if the hole is out of shape, maybe possible to drill it round and use a short snug sleeve over the peg to reduce any movement- just a thought ?  *dunno*..
Started building in about 1977/8 a on average '52 A10 -built from bits 'n pieces never resto intended -maybe 'personalised'
Have a '74 850T Moto Guzzi since '92-best thing I ever bought doesn't need a kickstart 'cos it bump starts sooooooooo(mostly) easy
Australia

Offline Sluggo

  • Serial Hoarder, or Eccentric Collector depending on viewpoint
  • Resident Legend
  • *****
  • Join Date: Jun 2017
  • Posts: 654
  • Karma: 11
Re: Engine breather
« Reply #6 on: 06.09. 2019 02:43 »
The cork washers are a pain, and have to be grind to correkt thickness. So I convert to use a spring to held the breather in place. Running in seval engine since thousands of miles with no problems.

cheers Klaus

Klaus is correct of course, but amusing people still using cork washers, along with other Colonial pursuits.  However,,,, *eek*  If you wish to truly master proper end float, shimming and use of proper materials than nothing can compare to shop notes from the Hurley Pugh collective, especially those shims & washers!.....to wit:

" With the crankshaft in the correct position, remove the six bolts that secure the magneto to the top side of the crankcases. You will notice that all of the bolts are different lengths - it is crucial that these are replaced in the correct holes otherwise you will lock the gearbox solid. Underneath the magneto you will almost certainly find one or more thin shims, fitted by previous owners. Hurley-Pugh itself did not actually shim the magnetos when the engines were originally manufactured. Instead, Bill "Masher" Stubbings precisely adjusted the magneto's mounting points by the careful application of a large hammer. If you look closely, you'll probably still be able to see the dents in the top of the crankcase where "Masher" skilfully wielded his scarred hammer. As Hurley-Pugh did not shim the magneto it didn't produce any shims; again, the Hurley-Pugh Enthusiasts Club can oblige with a set of paper shims for a reasonable 280 pounds complete.

Inspection

With the magneto removed, examine the teeth on both the gearwheel and the conrod for signs of distress. Any evidence of chipping, bending, burring or missing teeth will require replacement of both the magneto gear and the conrod, as well as a complete engine strip to remove the debris.

The leather friction washer can be found between the gearwheel and the magneto. To inspect this, use a blowtorch to heat the gearwheel to cherry red and use a 400lb press to ease it off the shaft. The heating process usually destroys the leather washer so it will need to be replaced regardless. Note that the washer is made from treated rabbit skin; some unscrupulous suppliers are selling washers made from inferior cow leather but these parts will not impart the correct amount of friction so should be avoided. The easiest way to test if a washer is from cow or rabbit leather is to send it off for DNA testing.

Adjustment of Friction Washer

The precise amount of friction that the washer imparts on the magneto shaft is crucial to ensuring correct alignment of the gear teeth in operation. Adjustment is obtained by moving the gearwheel slightly in or out on the shaft. The friction is at the correct setting if, with the magneto at operating temperature (60 degrees centigrade for European models, 70 degrees for Empire models - pad the magneto in clean towels and put it in the family tumble dryer until it is at the correct temperature) you should be able to ease the ungummed edge of a Rizla Green King Size cigarette paper - note, NOT Rizla Red - between the magneto body and the washer. If there is insufficient clearance, allow the magneto to cool then prise the gearwheel away from the magneto with a large tyre iron. If there is excessive clearance, tap the gear with a hammer.
Remember that any advice received on a free internet forum is generally worth about 1/2 of what you paid for it.
We overcharge every 3rd customer to pass the savings onto you.
You can have High Quality, Low price, and fast turnaround. Pick any 2, Never all 3 at the same time.

Online BigJim

  • Resident Legend
  • *****
  • Join Date: Aug 2018
  • Posts: 537
  • Karma: 2
  • Bristol. UK
Re: Engine breather
« Reply #7 on: 06.09. 2019 08:18 »
Thank you Sluggo,has cheered me up, now off to work.
Jamie,  Supporter of Distinguished Gentleman's Ride

Offline Swarfcut

  • Wise & Enlightened
  • *
  • Join Date: Oct 2018
  • Posts: 2201
  • Karma: 54
Re: Engine breather
« Reply #8 on: 06.09. 2019 09:19 »
Sluggo.  Hurley-Pugh were in the vanguard of engine development, prototypes featuring the first hand carved connecting rods, the material chosen being the pallet wood that came with deliveries of fine Chinese Silk Wiping Rags. Nothing was wasted, any material to hand was used, hence their great commercial success and world leading innovations.
  Cylinder bores were honed and finally the pistons were lapped and the bores polished to a mirror, low friction surface finish with a compound said to comprise 1/8" gravel, road tar and workshop floor sweepings. The fine metallic, mineral and hydrocarbon residue from this process was stirred "in vaccuo" with poxy resin and  used to treat the rabbit skin friction washer, as detailed above, producing a highly prized, rare and variable quality component, the benchmark for today's so called "pattern parts"
 

 Other Forum members may have more information and this thread may even merit a section of its own before the original breather post gets diverted.

Swarfy.

Online muskrat

  • Global Moderator
  • Wise & Enlightened
  • **
  • Join Date: Jul 2009
  • Posts: 10762
  • Karma: 130
  • Lithgow NSW Oz
    • Shoalhaven Classic Motorcycle Club Inc
Re: Engine breather
« Reply #9 on: 08.09. 2019 09:14 »
G'day BJ.
I like duTch have used 0.4mm oil jointing behind the cork to space it out a tad.
Cheers
'51 A7 plunger, '57 A7SS racer now a A10CR, '78 XT500, '83 CB1100F, 88 HD FXST, 2000 CBR929RR ex Honda Australia Superbike .
Australia
Muskys Plunger A7

Online morris

  • Wise & Enlightened
  • *
  • Join Date: Aug 2012
  • Posts: 1765
  • Karma: 27
  • Antwerp, Belgium
Re: Engine breather
« Reply #10 on: 10.09. 2019 22:36 »
G'day BJ.
I like duTch have used 0.4mm oil jointing behind the cork to space it out a tad.
Cheers
Ah... there’s another oil thread... *yeah*
I use Penstrol 20/100 high bollocks content for that...
'58 BSA A 10 SA
'52 BSA A 10 Plunger
'55 MORRIS ISIS
The world looks better from a motorbike
Belgium

Offline Swarfcut

  • Wise & Enlightened
  • *
  • Join Date: Oct 2018
  • Posts: 2201
  • Karma: 54
Re: Engine breather
« Reply #11 on: 12.09. 2019 16:54 »
Morris, that grade is a little light for the riding you do. White Star Line Lubricants do a grade that may be more suitable, covering temperatures from the Tropics to the Poles.

Swarfy.