Author Topic: A10 revs hanging when hot.  (Read 1431 times)

Offline K1100

  • A's Good Friend
  • ***
  • Join Date: Aug 2012
  • Posts: 50
  • Karma: 1
  • 1954 A10
A10 revs hanging when hot.
« on: 21.05. 2020 13:18 »
Hi everyone. Since last week my 1954 swinging arm A10 is back on the road after 7 years standing. It was well laid up so has started easily and is running nicely. But....
I now remember the slight issue I had 7years ago when I first bought it. It starts very easily after a tickle, with no choke, and settles into a nice steady tick over and throttle response is good.
But when it is hot the revs drop slowly when I shut the throttle. They do drop, but so slowly.
I have searched this section and see that either a sticking slide or blocked pilot jet might be the cause. It has an Amal Monobloc. What should be the first and easiest thing for me to check, please?

Online Triton Thrasher

  • Scotland
  • Wise & Enlightened
  • *
  • Join Date: Feb 2009
  • Posts: 1928
  • Karma: 23
Re: A10 revs hanging when hot.
« Reply #1 on: 21.05. 2020 13:56 »
Can you hear the slide close with a “click?”

Classic causes are pilot mixture adjusted too weak, air leak into manifold, auto advance sloppy or sticky.

Offline Swarfcut

  • Wise & Enlightened
  • *
  • Join Date: Oct 2018
  • Posts: 2201
  • Karma: 54
Re: A10 revs hanging when hot.
« Reply #2 on: 21.05. 2020 14:44 »
May be nothing more than a dry or tightly routed throttle cable, but as a first step check the slide. Grit, varnish from old fuel and carbon build up are easily removed with a dose of carb cleaner.

 As TT says, it should close with a definite click. While the top is off the carb.....check  the slide actually has a return spring that works, and it does not bind on the choke slide. Applies to 276 and monobloc types.

 Earlier post in this section details a typical problem and cure for a sticking slide.

 Swarfy.

Offline K1100

  • A's Good Friend
  • ***
  • Join Date: Aug 2012
  • Posts: 50
  • Karma: 1
  • 1954 A10
Re: A10 revs hanging when hot.
« Reply #3 on: 21.05. 2020 18:38 »
Hi Swarfy and Thrasher. Throttle closes with solid click hot or cold. Found that the pilot jet cover nut was loose so have tightened that (after making a cutaway in the side of the drip tray so I could move a spanner).That doesn't seem to have changed anything so is carb removal to take out and clean pilot jet next do you think?  The drip tray gets right in the way of the pilot jet.

Offline muskrat

  • Global Moderator
  • Wise & Enlightened
  • **
  • Join Date: Jul 2009
  • Posts: 10760
  • Karma: 130
  • Lithgow NSW Oz
    • Shoalhaven Classic Motorcycle Club Inc
Re: A10 revs hanging when hot.
« Reply #4 on: 21.05. 2020 20:28 »
G'day K1100.
Sounds like an air leak to me (as well as above suggestions). All good cold/warm after a tickle up but when hot and the carb grows a little (more than the head) you may have a leak at the flange. A quick check is to get her hot and spray some WD/carb clean around the flange and listen for revs to drop or increase. Also spray around the top cap and cable entry.
Cheers
'51 A7 plunger, '57 A7SS racer now a A10CR, '78 XT500, '83 CB1100F, 88 HD FXST, 2000 CBR929RR ex Honda Australia Superbike .
Australia
Muskys Plunger A7

Offline trevinoz

  • Newcastle, N.S.W. Australia.
  • Wise & Enlightened
  • *
  • Join Date: Jul 2006
  • Posts: 3184
  • Karma: 71
Re: A10 revs hanging when hot.
« Reply #5 on: 21.05. 2020 22:37 »
Is your slide worn out?

Offline KiwiGF

  • Last had an A10 in 1976, in 2011 it was time for my 2nd one. It was the project from HELL (but I learned a lot....)
  • Wise & Enlightened
  • *
  • Join Date: Feb 2011
  • Posts: 1933
  • Karma: 17
Re: A10 revs hanging when hot.
« Reply #6 on: 22.05. 2020 01:13 »
Do you have a choke cable? If not is the hole in the top of the carb blocked off?

Mine used to have an erratic tickover when hot, tickover revs increased randomly, cause was a worn slide, solution new burlen amal.
New Zealand

1956 A10 Golden Flash  (1st finished project)
1949 B31 rigid “400cc”  (2nd finished project)
1968 B44 Victor Special (3rd finished project)
2001 GL1800 Goldwing, well, the wife likes it
2009 KTM 990 Adventure, cos it’s 100% nuts

Offline K1100

  • A's Good Friend
  • ***
  • Join Date: Aug 2012
  • Posts: 50
  • Karma: 1
  • 1954 A10
Re: A10 revs hanging when hot.
« Reply #7 on: 22.05. 2020 09:13 »
Hi Kiwi GF, Muskrat and Trevinos. I’ll work through those suggestions ...thank you. I can see from the file of receipts that came with the bike that the carb was new 11,000 miles ago which I am thinking should mean it is ok inside.
Best wishes to all.

Offline groily

  • Wise & Enlightened
  • *
  • Join Date: Jul 2007
  • Posts: 1844
  • Karma: 31
    • www.brightsparkmagnetos.com
Re: A10 revs hanging when hot.
« Reply #8 on: 22.05. 2020 10:01 »
You'd think it would and should be good - but a new 389 on mine, the slide was dead in less than that mileage and I replaced it with the better anodised version. Which IMHO ought to be the standard fitment, not a pay-more-for extra. Presumably they exist because it's well-known the cheese-metal ones aren't much good!
Mine was both 'sticky' in operation in the bore and 'rattly' when closed, which is kind of counter-intuitive, but it was what it was. (The bore was still good luckily.)
Bill

Offline a101960

  • Wise & Enlightened
  • *
  • Join Date: Sep 2007
  • Posts: 1072
  • Karma: 12
  • BSA RGS BSA C12
Re: A10 revs hanging when hot.
« Reply #9 on: 22.05. 2020 10:27 »
Don't know if they still do, but Surrey Cycles used to do chrome plated slides. I bought my 389 from them and that's how it was delivered. My slide has never shown any sign of wear.

Offline Butch (cb)

  • Wise & Enlightened
  • *
  • Join Date: Aug 2010
  • Posts: 1691
  • Karma: 16
Re: A10 revs hanging when hot.
« Reply #10 on: 22.05. 2020 13:00 »
Slide wear presumably has some dependency of the presence of an air filter and the environment you normally ride in?
Warning - observations made by this member have a 93% unreliability rating.

Of Bikes; various, including ...
'58 S/Arm Iron Head Flash Bitza


Offline K1100

  • A's Good Friend
  • ***
  • Join Date: Aug 2012
  • Posts: 50
  • Karma: 1
  • 1954 A10
Re: A10 revs hanging when hot.
« Reply #11 on: 22.05. 2020 17:49 »
The change from instant shut-down to slow shut down occurs within 2 mins at tick over. Today I dribbled oil over the carb/manifold joint but couldn’t sense any improvement.

Tomorrow I will remove the carb and remake the joint with new gaskets, to be certain there is n9 leak there.

If the pilot jet is the issue, is it that it is not properly adjusted or that it is blocked?

Removing the carb gives me access to check it... the drip tray gets in the way at the moment. *sad2*

Offline RDfella

  • Wise & Enlightened
  • *
  • Join Date: Aug 2017
  • Posts: 2193
  • Karma: 15
Re: A10 revs hanging when hot.
« Reply #12 on: 22.05. 2020 20:03 »
Sounds like a modern car - they take ages to drop to a tickover - apparently otherwise they'd stall because of their lean burn. Makes them unpleasant to drive. In your case, sounds like a too-rich slow running mixture.
'49 B31, '49 M21, '53 DOT, '58 Flash, '62 Flash special, '00 Firestorm, Weslake sprint bike.

Offline K1100

  • A's Good Friend
  • ***
  • Join Date: Aug 2012
  • Posts: 50
  • Karma: 1
  • 1954 A10
Re: A10 revs hanging when hot.
« Reply #13 on: 23.05. 2020 10:27 »
Hi RD Fella... thank you,  that’s high up on the list to check, and I am still surprised that the drip tray stops me getting any tool to the pilot jet to work on it.

Offline K1100

  • A's Good Friend
  • ***
  • Join Date: Aug 2012
  • Posts: 50
  • Karma: 1
  • 1954 A10
Re: A10 revs hanging when hot.
« Reply #14 on: 23.05. 2020 11:51 »
The pilot jet is not making sense to me. When I unscrewed the pilot jet retaining nut the float chamber contents drained out. The pilot jet was loose. The retaining nut screws onto the jet so I can't see how to adjust it. Wherever I set it - say 1 1/2 turns out - it will screw back in as I thread the retaining nut onto it. What am I missing?(apart from a brain)
And how is it possible to adjust tickover while the engine is running if the fuel drains out? Haynes is useless and I can't find anything online that helps.