Author Topic: hub adaptor  (Read 532 times)

Offline derek taylor

  • A's Best Friend
  • ***
  • Join Date: Mar 2014
  • Posts: 134
  • Karma: 2
  • 1959 golden flash
hub adaptor
« on: 19.03. 2015 19:40 »
just  put the clutch back together ( 4 spring ) new rollers & a new hub adapter, got a problem with it it's as if the pushrod is now to short ie the clutch leaver is about at the handle bars before theres any movement at the clutch also it looks like the chain wheel ( basket ) is a slight bit further out than it used to be, when i fitted it all together i gave the hub adaptor a couple of good tap's with a small hammer to make sure it was fully home, it went together no trouble at all.  was just thinking maby the new hub adaptor is a slight different to the old one,  anyone else had the same problem?

Offline morris

  • Wise & Enlightened
  • *
  • Join Date: Aug 2012
  • Posts: 1582
  • Karma: 24
  • Antwerp, Belgium
Re: hub adaptor
« Reply #1 on: 19.03. 2015 20:04 »
I assume, as it's a 4 spring clutch, it sits on a taper shaft? If so the adapter's taper hole could be a tad smaller than the old one. Doesn't need much to make it sit significantly less deep on the shaft.
Also, if you fitted the woodruff key, it's possible that its the key that prevents the adapter to slide fully home.
'58 BSA A 10 SA
'52 BSA A 10 Plunger
'55 MORRIS ISIS
The world looks better from a motorbike
Belgium

Offline derek taylor

  • A's Best Friend
  • ***
  • Join Date: Mar 2014
  • Posts: 134
  • Karma: 2
  • 1959 golden flash
Re: hub adaptor
« Reply #2 on: 19.03. 2015 20:35 »
i'm sure the adaptor went fully home there was no movement on it.

Online trevinoz

  • Newcastle, N.S.W. Australia.
  • Wise & Enlightened
  • *
  • Join Date: Jul 2006
  • Posts: 2888
  • Karma: 67
Re: hub adaptor
« Reply #3 on: 19.03. 2015 20:43 »
Derek,
               First check your primary sprockets are aligned with a straight edge, this will tell if your adaptor is on far enough.
If OK, adjust the pushrod to suit.

Offline KiwiGF

  • Last had an A10 in 1976, in 2011 it was time for my 2nd one. It was the project from HELL (but I learned a lot....)
  • Wise & Enlightened
  • *
  • Join Date: Feb 2011
  • Posts: 1448
  • Karma: 12
Re: hub adaptor
« Reply #4 on: 19.03. 2015 20:48 »
I dont know about the triumph clutch centres but there is a well known issue with some 6 spring centres having incorrect tapers causing the sort of problems you are having, and suppliers that keep selling them even when they are aware they are no good, maybe compare your old one with the new one?

New plates if you ftted them will probably result in having to adjust the clutch of course *smile*, but would not cause the chainwheel to be out of alignment.

There is provision to shim the front sprocket if the mis alignment is not too big?

New Zealand

1956 A10 Golden Flash (1st finished project)

1949 B31 rigid “400cc hot rod” (2nd finished project, + favourite bike)

1949 C11 rigid, but why!!! (cos it was cheap)

1937 B21, project missing parts, mission impossible?

GL1800 Goldwing, well, the wife likes it

KTM 950 ADV, cos it’s 100% nuts

1952 Armstrong Siddeley Whitley for rainy days (with wife

Online chaterlea25

  • Wise & Enlightened
  • *
  • Join Date: Jun 2009
  • Posts: 3212
  • Karma: 46
Re: hub adaptor
« Reply #5 on: 19.03. 2015 20:58 »
Hi Derek,
What else did you change at the same time? new clutch plates will affect pushrod length
Yes there are a lot of "different" interpetations of the adaptor  *sad2*

There are a lot of previous postings on the subject  *????* *????* please do a search and then ask if you need more clarification

It is vitally important for reliability to get the primary sprockets properly aligned *warn* *warn* *warn*
You dont want the chain to snap and do wreck *pull hair out*

John
1961 Super Rocket
1963 RGS (ongoing)

Offline derek taylor

  • A's Best Friend
  • ***
  • Join Date: Mar 2014
  • Posts: 134
  • Karma: 2
  • 1959 golden flash
Re: hub adaptor
« Reply #6 on: 19.03. 2015 21:17 »
just changed the roller bearings & hub adaptor

Online chaterlea25

  • Wise & Enlightened
  • *
  • Join Date: Jun 2009
  • Posts: 3212
  • Karma: 46
1961 Super Rocket
1963 RGS (ongoing)

Offline derek taylor

  • A's Best Friend
  • ***
  • Join Date: Mar 2014
  • Posts: 134
  • Karma: 2
  • 1959 golden flash
Re: hub adaptor
« Reply #8 on: 20.03. 2015 06:43 »
a good read *smiley4*