Author Topic: A10 bushings  (Read 1142 times)

Offline Marqs1979

  • A's Best Friend
  • ***
  • Join Date: Sep 2013
  • Posts: 109
  • Karma: 0
A10 bushings
« on: 05.01. 2014 16:17 »
Hello!
I intend to produce several new bushings in the engine and gearbox. How much larger the hole in the bushing to be than the diameter of the shaft?
Good Advice
0
No reactions

Online muskrat

  • Global Moderator
  • Wise & Enlightened
  • **
  • Join Date: Jul 2009
  • Posts: 8442
  • Karma: 111
  • Lithgow NSW Oz
    • Shoalhaven Classic Motorcycle Club Inc
Re: A10 bushings
« Reply #1 on: 05.01. 2014 19:03 »
G'day Marqs, the general rule is 1 to 1.5 thou. But with crush on the bush when installed it will close up. Always, if at all possible, heat case to drop in bush and line ream bush to fit shaft.
Cheers
Good Advice
0
No reactions
'51 A7 plunger, '57 A7SS now A10CR,  '83 CB1100F, 88 FXST .
Australia
Muskys Plunger A7

Offline Marqs1979

  • A's Best Friend
  • ***
  • Join Date: Sep 2013
  • Posts: 109
  • Karma: 0
Re: A10 bushings
« Reply #2 on: 07.01. 2014 16:25 »
G'day Marqs, the general rule is 1 to 1.5 thou. But with crush on the bush when installed it will close up. Always, if at all possible, heat case to drop in bush and line ream bush to fit shaft.
Cheers

Hello!

Do you mean from 0.01 to 0.015 millimeters larger than the shaft?

Regards / Markus
Good Advice
0
No reactions

Offline Topdad

  • bob hebdon
  • Wise & Enlightened
  • *
  • Join Date: May 2011
  • Posts: 2250
  • Karma: 32
  • l
Re: A10 bushings
« Reply #3 on: 07.01. 2014 16:48 »
Hi Marqs, no not mm would be imperial size . a thousandth of and inch  0.0001 = imperial where 25.4mm= 1 inch. My maths is useless but thats the basic oneof our engineers will explain far better than I but thats the jist of it. regards BobH
Good Advice
0
No reactions
" rules are made for the guidance of wise men and the blind obediance of fools"
United Kingdom

Online RichardL

  • Outside Chicago, IL
  • Wise & Enlightened
  • *
  • Join Date: Nov 2007
  • Posts: 5163
  • Karma: 49
Re: A10 bushings
« Reply #4 on: 07.01. 2014 18:14 »
0.001" (a "thousandth") = 0.0254 mm  

Bob, One too many zeros makes it a "ten thousandth" (0.0001"). A typo, I beleive. Now, if I only knew something about motorcycles.
Good Advice
0
No reactions
Plan on signing up for the world-wide 2020 DISTINGUISHED GENTLEMAN'S RIDEon September 27, 2020. This year it's a solo or pillion ride in dapper attire. Watch website at https://www.gentlemansride.com for details.


Offline Marqs1979

  • A's Best Friend
  • ***
  • Join Date: Sep 2013
  • Posts: 109
  • Karma: 0
Re: A10 bushings
« Reply #5 on: 07.01. 2014 18:39 »
Thanks  *smile*
Good Advice
0
No reactions

Offline A10rocket

  • Moving Up
  • **
  • Join Date: Feb 2010
  • Posts: 22
  • Karma: 0
  • Lancashire UK
Re: A10 bushings
« Reply #6 on: 07.01. 2014 23:49 »
Hi, 
the rule of thumb is  0.001" - 0.0015" per inch of diameter.

So if you have a three quarter inch shaft ,the clearance needs to be  0.750" x 0.001" = 0.00075" for the lower limit,
                                                                 
                                                                                             0.750" x 0.0015" = 0.0011" for the upper limit,                       
  This info is from an engineering hand book .

   Regards Ken.
Good Advice
0
No reactions
1961 Super Rocket

Offline Topdad

  • bob hebdon
  • Wise & Enlightened
  • *
  • Join Date: May 2011
  • Posts: 2250
  • Karma: 32
  • l
Re: A10 bushings
« Reply #7 on: 08.01. 2014 10:01 »
Thanks Richard, typical financial adviser -- can't add up properly-- I knew someone would sort it out for our friend, regards BobH.
Good Advice
0
No reactions
" rules are made for the guidance of wise men and the blind obediance of fools"
United Kingdom

Offline Marqs1979

  • A's Best Friend
  • ***
  • Join Date: Sep 2013
  • Posts: 109
  • Karma: 0
Re: A10 bushings
« Reply #8 on: 11.02. 2014 16:44 »
G'day Marqs, the general rule is 1 to 1.5 thou. But with crush on the bush when installed it will close up. Always, if at all possible, heat case to drop in bush and line ream bush to fit shaft.
Cheers

You can buy a special reamer somewhere?
Good Advice
0
No reactions