Author Topic: wiring question  (Read 1236 times)

Offline Baggy

  • Moving Up
  • **
  • Join Date: Jun 2008
  • Posts: 25
  • Karma: 0
wiring question
« on: 17.07. 2008 22:04 »
Evenin' chaps  *smiley4*, I have kinda covered my wing diagramme in paint and need some help please (again) I have got me a reg rec as recommended from a member on the site, a neat little solid state ,and its useable in a 6 or 12 volt application, I going to be running 6V positive earth, there is one wire that I cannot see where it goes to run 6V, if running 12 then its not connected just insulated off, its a white wire that goes to A, I have emailed the guy who supplied it and stupidly did it through my works email and I'm not in again till tuesday!!!does anyone know what A is, my guess would be ammetre but I'm not going to be using one,
cheers
Baggy

Offline a10gf

  • Wise & Enlightened
  • *
  • Join Date: Sep 2006
  • Posts: 2686
  • Karma: 42
  • West Coast, Norway & Alpes Maritimes, France
    • A10 GF
Re: wiring question
« Reply #1 on: 17.07. 2008 23:16 »
Hello, see http://manortec.co.uk/dvr2-data.pdf 

As i understand it:
White lead to A (Brown) for 6v. So you'll get the 6v by joining these 2 leads to 'feed' the battery (trough ammeter or not).

I would recommend fitting a fuse at the battery output.

Hope this helps.

A10 GF '53 My A10 website
"Success only gets you a ticket to a much more difficult task"

Online Brian

  • Wise & Enlightened
  • *
  • Join Date: May 2007
  • Posts: 1699
  • Karma: 40
  • Mt Gambier, South Australia.
Re: wiring question
« Reply #2 on: 18.07. 2008 02:17 »
This should help. I think the + earth units are different to the -earth ones. I have had one of these fitted to my A10 for a couple of months now and it has worked perfectly.      Brian.

Online groily

  • Wise & Enlightened
  • *
  • Join Date: Jul 2007
  • Posts: 1045
  • Karma: 17
    • www.brightsparkmagnetos.com
Re: wiring question
« Reply #3 on: 18.07. 2008 07:03 »
I've got 2 of these DVR2 things, one working at 12v, one at 6. As I have said a time or two, they are the best regulators I have had. Several friends say the same. Work very well for Lucas or Miller gear, in + or - earth. Mike Hutchings the supplier will reply to your note for sure. In the meantime, for 12 volt you leave one wire unconnected as it says on the bit of paper that comes with; for 6 volt you double up the 2 wires. Have a look at the link a10gf provided and it should all be pretty clear. Clearer than writing it out here.

(One very small point for the avoidance of any confusion:  - the DVR2 isn't a 'reg rec' - your dynamo only produces DC so doesn't need the output rectifying. They are just electronic voltage regulators/cut-outs. Reg rectifiers can be got - I have one on another bike - as a modern replacement for a selenium rectifier plus zener diode as used with 2 wire alternators. Just as simple rectifiers can also be got - as used with the older 3 wire alternators which relied on the lighting switch to cut in and out extra coils on the alternator for the delivery of more or less juice depending on load.)

If you're not going to have an ammeter, all the more reason to have decent fuse protection as you'll have nothing to tell you what's going on or gone wrong. For 6v, suggest a 15A fuse in the main battery line. Personally, I'd never be without an ammeter on these things, or indeed on any classic vehicle, as they are all, ahem, subject to the occasional electrical foible. Which is why, again and again to the point of boring people to death, I thank the powers-that-were for the magneto . . . .
Bill